US · EN
0

Maintenance and repair Suzuki GT750-B (PvM)

This project is finished and the SUZUKI GT750 can be returned to the owner.
This project is finished and the SUZUKI GT750 can be returned to the owner.
This project is finished and the SUZUKI GT750 can be returned to the owner.
Here is the "new" connector on a view inside. This will give no problems by using it. This was the last job to do on this SUZULKI GT750. This GT750 can go back to his owner.
Here is the "new" connector on a view inside. This will give no problems by using it. This was the last job to do on this SUZULKI GT750. This GT750 can go back to his owner.
The repaired rectifier of th eclient, now it is usable again on the clients GT750.
The repaired rectifier of th eclient, now it is usable again on the clients GT750.
NEVER throw away defect parts of the GT. The rectifier above has a shortcut, so we used the connector itself and the wires to repair the burned connector of the installed rectifier.
NEVER throw away defect parts of the GT. The rectifier above has a shortcut, so we used the connector itself and the wires to repair the burned connector of the installed rectifier.
For testing we connected the wires without the connector cap into the wire loom of the GT750.
For testing we connected the wires without the connector cap into the wire loom of the GT750.
On a running GT750 engine OIL PUMP TEST performed en OK. The oil lines are being filled with the red 2stroke oil.
On a running GT750 engine OIL PUMP TEST performed en OK. The oil lines are being filled with the red 2stroke oil.
Adjusting the FUEL mix screw for getting the same exhaust temprature. This photo is AFTER adjusting the fuel mix screw. The exhaust temperature are all thre close to eachother.
Adjusting the FUEL mix screw for getting the same exhaust temprature. This photo is AFTER adjusting the fuel mix screw. The exhaust temperature are all thre close to eachother.
Adjusting the FUEL mix screw for getting the same exhaust temprature. This photo is BEFORE adjusting the fuel mix screw. You can see a large difference betwwen the exhaust temperature.
Adjusting the FUEL mix screw for getting the same exhaust temprature. This photo is BEFORE adjusting the fuel mix screw. You can see a large difference betwwen the exhaust temperature.
Synchronizing the carburettors: RIGHT to LEFT. The vacuum must be equel to both carburettors.
Synchronizing the carburettors: RIGHT to LEFT. The vacuum must be equel to both carburettors.
SITE UPDATE 06092025: Synchronizing the carburettors: RIGHT to CENTER. The vacuum must be equel to both carburettors.
SITE UPDATE 06092025: Synchronizing the carburettors: RIGHT to CENTER. The vacuum must be equel to both carburettors.
This (generator) connector looks very bad. It looks if it had become hot, we think due to high current (Ampére). Of course we will repair this bad connector.
This (generator) connector looks very bad. It looks if it had become hot, we think due to high current (Ampére). Of course we will repair this bad connector.
This (generator) connector looks very bad. It looks if it had become hot, we think due to high current (Ampére).
This (generator) connector looks very bad. It looks if it had become hot, we think due to high current (Ampére).
Installed the brake pedal and the steps for the rider himself.
Installed the brake pedal and the steps for the rider himself.
Installing the sprocket covers.
Installing the sprocket covers.
Secured the sprocket washer on three places.
Secured the sprocket washer on three places.
Just a view to see that is a lot of work to install the engine back in the frame.
Just a view to see that is a lot of work to install the engine back in the frame.
All parts to be installed: Oil pump which is prepared for the oil pump test, clutch cable, exhausts LH and RH, installing the chain, gear pedal etc etc.
All parts to be installed: Oil pump which is prepared for the oil pump test, clutch cable, exhausts LH and RH, installing the chain, gear pedal etc etc.
All parts to be installed: Oil pump which is prepared for the oil pump test, clutch cable, exhausts LH and RH, installing the chain, gear pedal etc etc.
SITE UPDATE 05092025: Today we will install the GT750 engine back in the frame. On the workbench we made the studs for the exhausts, and adjusted the ignition points.
SITE UPDATE 05092025: Today we will install the GT750 engine back in the frame. On the workbench we made the studs for the exhausts, and adjusted the ignition points.
Engine ready to install it back in the frame.
Engine ready to install it back in the frame.
Engine ready to install it back in the frame.
The pressure test on the cooling system of the GT750 engine has passed.
The pressure test on the cooling system of the GT750 engine has passed.
The pressure test on the cooling system of the GT750 engine has passed.
We always do a leak test on the cooling system of the GT750 engine. We close the lower radiator hose connection and install the pressure set on the radiator connection on the cylinderhead.
We always do a leak test on the cooling system of the GT750 engine. We close the lower radiator hose connection and install the pressure set on the radiator connection on the cylinderhead.
We always do a leak test on the cooling system of the GT750 engine. We close the lower radiator hose connection and install the pressure set on the radiator connection on the cylinderhead.
Elektrical starter engine cover installed to finish the connection of the By-Pass S-hose on the cylinderhead.
Elektrical starter engine cover installed to finish the connection of the By-Pass S-hose on the cylinderhead.
The By-Pass S-hose, we used genuine SUZUKI clamps, instead of COTS clamps, it is possible that they will leak.
The By-Pass S-hose, we used genuine SUZUKI clamps, instead of COTS clamps, it is possible that they will leak.
This is a newer type of the elektrical starter engine, the older types do not have enough power to start the GT750 engine itself.
This is a newer type of the elektrical starter engine, the older types do not have enough power to start the GT750 engine itself.
Installed REBUILD oil lines, SIX new check-valves have been installed and the installed elektrical starter engine, the cause this bike needded some maintenance, but ended in a total engine rebuild.
Installed REBUILD oil lines, SIX new check-valves have been installed and the installed elektrical starter engine, the cause this bike needded some maintenance, but ended in a total engine rebuild.
Installed the cylinderhead, torqued the bolts in the right sequence.
Installed the cylinderhead, torqued the bolts in the right sequence.
And there is a nut, M10x1,25, at the lower back of the barrel.
And there is a nut, M10x1,25, at the lower back of the barrel.
Of course an overview and a last check of the installed barrel and the pistons.
Of course an overview and a last check of the installed barrel and the pistons.
When the barrel is half way on it's place, we prefer to do this with two persons, always check if the O-rings under the footer gasket still are on their place.
When the barrel is half way on it's place, we prefer to do this with two persons, always check if the O-rings under the footer gasket still are on their place.
Install ALSO the FOUR O-rings under the footer gasket.
Install ALSO the FOUR O-rings under the footer gasket.
Do not forget to check if the oil canals in the footer gasket are OPEN. Sometimes the pressed gasket hole part will stick in the gasket. There are three hole sin total.
Do not forget to check if the oil canals in the footer gasket are OPEN. Sometimes the pressed gasket hole part will stick in the gasket. There are three hole sin total.
Do not forget to check if the oil canals in the footer gasket are OPEN. Sometimes the pressed gasket hole part will stick in the gasket. There are three hole sin total.
AFTER the pistons are installed, CHECK if the pistons are in the right place and in the right position.
AFTER the pistons are installed, CHECK if the pistons are in the right place and in the right position.
ALWAYS check if the piston circlip is installed in the right way, this is the other side....
ALWAYS check if the piston circlip is installed in the right way, this is the other side....
ALWAYS check if the piston circlip is installed in the right way, this is one side....
ALWAYS check if the piston circlip is installed in the right way, this is one side....
Use a lot of grease for these parts, WHEN a needle of the bearing will fall of it won't fall into the cylinder carter, and the parts has to stay in place when we install the piston.
Use a lot of grease for these parts, WHEN a needle of the bearing will fall of it won't fall into the cylinder carter, and the parts has to stay in place when we install the piston.
New bored and honed barrel.
New bored and honed barrel.
New bored and honed barrel.
Close up of the parts for installing the piston.
Close up of the parts for installing the piston.
SITE UPDATE 04092025: Today we will install the barrel back on the engine. Of course we need to prepare the pistons for installation, arranging the piston, piston rings, piston pin, smalll-end needle bearing, piston circlips and the thrust washers. NOTE The piston on the left is the RIGHT piston, the engine is flipped.
SITE UPDATE 04092025: Today we will install the barrel back on the engine. Of course we need to prepare the pistons for installation, arranging the piston, piston rings, piston pin, smalll-end needle bearing, piston circlips and the thrust washers. NOTE The piston on the left is the RIGHT piston, the engine is flipped.
Installed the three contra nuts m10x1,25.
Installed the three contra nuts m10x1,25.
SAFETY ISSUE: No contra nuts (3x M10x1,25) installed. It is possible that you will loose the side stand.
SAFETY ISSUE: No contra nuts (3x M10x1,25) installed. It is possible that you will loose the side stand.
Before the engine will be installed back in the frame we need to correct these safety issues. We corrected this already on the side stand bolt itself.
Before the engine will be installed back in the frame we need to correct these safety issues. We corrected this already on the side stand bolt itself.
SAFETY ISSUE: No contra nut (M10x1,25) installed. It is possible thai you will oloose the side stand.
SAFETY ISSUE: No contra nut (M10x1,25) installed. It is possible thai you will oloose the side stand.
We cleaned the frame of dust, sand and a lot of grease and oil.
We cleaned the frame of dust, sand and a lot of grease and oil.
We cleaned the frame of dust, sand and a lot of grease and oil.
Cleaning the frame before installing the engine back in the frame.
Cleaning the frame before installing the engine back in the frame.
SITE UPDATE 02092025: Cleaning the frame before installing the engine back in the frame.
SITE UPDATE 02092025: Cleaning the frame before installing the engine back in the frame.
And of course we routed the cables at the bottom of the engine. The cable guide for the ignition cable is installed at the left side so the ignition cable won't hit the exhaust.
And of course we routed the cables at the bottom of the engine. The cable guide for the ignition cable is installed at the left side so the ignition cable won't hit the exhaust.
........... and we installed the stator and the generator brushes of the generator.
........... and we installed the stator and the generator brushes of the generator.
....... the ignition points groundplate, repaired the hose on the wiring, ..........
....... the ignition points groundplate, repaired the hose on the wiring, ..........
SITE UPDATE 01092025: Today we installed all the elektrical stuff on the engine, as the gear psosition switch......
SITE UPDATE 01092025: Today we installed all the elektrical stuff on the engine, as the gear psosition switch......
The engine almost complete, of course there some things to do. We are waiting for the rebuild barrel.
The engine almost complete, of course there some things to do. We are waiting for the rebuild barrel.
The engine almost complete, of course there some things to do. We are waiting for the rebuild barrel.
The engine almost complete, of course there some things to do. We are waiting for the rebuild barrel.
The engine almost complete, of course there some things to do. We are waiting for the rebuild barrel.
We needed to rebuild the ignition cover, by replacing the two bearing, this because the ingnition shaft was wobbling to much. When the ignition shaft is wobbling to much, is possible that you can't adjust your ignition points properly.
We needed to rebuild the ignition cover, by replacing the two bearing, this because the ingnition shaft was wobbling to much. When the ignition shaft is wobbling to much, is possible that you can't adjust your ignition points properly.
Finished installing the starter clutch.
Finished installing the starter clutch.
Starter clutch nut should be torqued at 50Nm.
Starter clutch nut should be torqued at 50Nm.
The former rebuilder of this engine forgot to torque the nut of the starter clutch, we did it right this time because and we have made notes for critical assembling poinst.
The former rebuilder of this engine forgot to torque the nut of the starter clutch, we did it right this time because and we have made notes for critical assembling poinst.
Imnstalling the starter clutch bearings and of course we replaced the broken Woodruf-Key in the crankshaft.
Imnstalling the starter clutch bearings and of course we replaced the broken Woodruf-Key in the crankshaft.
Installing the release mechanism of the clutch after we replaced the seal of the release mechnism. Replaced also the kickstarter seal in this cover.
Installing the release mechanism of the clutch after we replaced the seal of the release mechnism. Replaced also the kickstarter seal in this cover.
Insatlling of the clutch finished, at the left you see the spring for the kickstarter.
Insatlling of the clutch finished, at the left you see the spring for the kickstarter.
Installed the clutch basket ande clutch drum, secured the nut on THREE places.
Installed the clutch basket ande clutch drum, secured the nut on THREE places.
Installed OIL plate for the secundaire shaft, istalled the shim and the plate for the clutch.
Installed OIL plate for the secundaire shaft, istalled the shim and the plate for the clutch.
Closed GT750 engine, ready for installing the other engine parts.
Closed GT750 engine, ready for installing the other engine parts.
Closed GT750 engine, ready for installing the other engine parts.
Don't forget the blind cap at the driven shaft of the gearbox.
Don't forget the blind cap at the driven shaft of the gearbox.
All casing surfaces should have enough sealant, but not as much as this engine had before. Don't forget the square centimeter between the bearings.
All casing surfaces should have enough sealant, but not as much as this engine had before. Don't forget the square centimeter between the bearings.
All casing surfaces should have enough sealant, but not as much as this engine had before. Don't forget the square centimeter between the bearings.
All casing surfaces should have enough sealant, but not as much as this engine had before. Don't forget the square centimeter between the bearings.
A check we do before closing the engine, checking the gaps between the crankshaft seal and the nearby crankshaft web and checking if the seals are in line with the bearings.
A check we do before closing the engine, checking the gaps between the crankshaft seal and the nearby crankshaft web and checking if the seals are in line with the bearings.
A check we do before closing the engine, checking the gaps between the crankshaft seal and the nearby crankshaft web and checking if the seals are in line with and leaning to the bearings.
A check we do before closing the engine, checking the gaps between the crankshaft seal and the nearby crankshaft web and checking if the seals are in line with and leaning to the bearings.
A check we do before closing the engine, checking the gaps between the crankshaft seal and the nearby crankshaft web and checking if the seals are in line with and leaning to the bearings.
A check we do before closing the engine, checking the gaps between the crankshaft seal and the nearby crankshaft web and checking if the seals are in line with and leaning to the bearings.
A check we do before closing the engine, checking the gaps between the crankshaft seal and the nearby crankshaft web and checking if the seals are in line with and leaning to the bearings.
A PIECE OF ART, the total rebuild crankshaft for this engine. This part weighs 19kg.
A PIECE OF ART, the total rebuild crankshaft for this engine. This part weighs 19kg.
Don't forget the large C-ring for the crankshaft.
Don't forget the large C-ring for the crankshaft.
Washer ON TOP of the oil pump shaft.
Washer ON TOP of the oil pump shaft.
All screws are locked.
All screws are locked.
Plug in the driven shaft installed (SO DON't FORGET).
Plug in the driven shaft installed (SO DON't FORGET).
The plug should be installed (SO DON't FORGET) , the hole in the kickstarter shaft should be in the UP position.
The plug should be installed (SO DON't FORGET) , the hole in the kickstarter shaft should be in the UP position.
Assembling the GT750 engine. First we do al the parts for the gearbox. In the next pictures a lot of points for CHECKING things if it is done right.
Assembling the GT750 engine. First we do al the parts for the gearbox. In the next pictures a lot of points for CHECKING things if it is done right.
SITE UPDATE 28082025 : Assembling the GT750 engine. First we do al the parts for the gearbox. In the next pictures a lot of points for CHECKING things if it is done right.
SITE UPDATE 28082025 : Assembling the GT750 engine. First we do al the parts for the gearbox. In the next pictures a lot of points for CHECKING things if it is done right.
Installed the by-pass bleeder oil/water line inside the engine. Checked the banjo connection are OK.
Installed the by-pass bleeder oil/water line inside the engine. Checked the banjo connection are OK.
Installed the gear forks and the gear selector drum alredy. Sadly now we have to wait for parts for reparing the engine.
Installed the gear forks and the gear selector drum alredy. Sadly now we have to wait for parts for reparing the engine.
Installed the SRIS valves with new filters. Of course we tested these SRIS valves, are OK, before installing.
Installed the SRIS valves with new filters. Of course we tested these SRIS valves, are OK, before installing.
Waterpump housing closed, waterpump job done.
Waterpump housing closed, waterpump job done.
Always check if the large circlip is placed above the waterpump.
Always check if the large circlip is placed above the waterpump.
Preparing to insert the waterpump in the engine housing. Always use some grease so it will go in smoothly without damaging the outside O-rings.
Preparing to insert the waterpump in the engine housing. Always use some grease so it will go in smoothly without damaging the outside O-rings.
We can start to assemble the GT750 engine. Installing the waterpump, left is the old waterpump which we couldn't use again due to a severe corroded water pump shaft. We have replaced the complete waterpump by a 100% refurbished waterpump.
We can start to assemble the GT750 engine. Installing the waterpump, left is the old waterpump which we couldn't use again due to a severe corroded water pump shaft. We have replaced the complete waterpump by a 100% refurbished waterpump.
SITE UPDATE 26082025: Cleaning the cilinderhead, so we can use this on the new engine again. Also tested the thermostat and is OK.
SITE UPDATE 26082025: Cleaning the cilinderhead, so we can use this on the new engine again. Also tested the thermostat and is OK.
As you can see, this engine has been opend at least TWICE, red sealant and A LOT OF grey sealant. No you don't need sealant as much as this. Also the crankshaft SEAL SEATS were corroded what looked like corrosion of the last 50years, someone didn't clean the seal seats of the engine before.
As you can see, this engine has been opend at least TWICE, red sealant and A LOT OF grey sealant. No you don't need sealant as much as this. Also the crankshaft SEAL SEATS were corroded what looked like corrosion of the last 50years, someone didn't clean the seal seats of the engine before.
Cleaning the upper casing of the engine, these engine parts are OK.
Cleaning the upper casing of the engine, these engine parts are OK.
Cleaning the lower case of the engine, these engine parts are OK.
Cleaning the lower case of the engine, these engine parts are OK.
Cleaning the engine parts. This is the barrel, due to the rust in the cylinder head top you can see that the head gasket has leaked every where.
Cleaning the engine parts. This is the barrel, due to the rust in the cylinder head top you can see that the head gasket has leaked every where.
The dogs of the THIRD gear aren't worn much so that will be OK.
The dogs of the THIRD gear aren't worn much so that will be OK.
The gearbox looks OK. Due to the rock solid sprocket nut we will replace the large bearing on the secundairy shaft. 26082025: Someone did a bad job on the crankshaft: At least a big-end or a small-end is defect, and the crankshaft was far out of tolerance: LEFT wobble: 0,09mm Right wobble: 0,14mm.
The gearbox looks OK. Due to the rock solid sprocket nut we will replace the large bearing on the secundairy shaft. 26082025: Someone did a bad job on the crankshaft: At least a big-end or a small-end is defect, and the crankshaft was far out of tolerance: LEFT wobble: 0,09mm Right wobble: 0,14mm.
Inside the waterpump, it's wet. It has leaked coolant.
Inside the waterpump, it's wet. It has leaked coolant.
Severe corroded waterpump shaft. Nope you can not use this shaft again. The waterpump will always leak coolant. Sadly you can buy ALL waterpump parts, but NOT the waterpump shaft. We need to replace the waterpump by a new one.
Severe corroded waterpump shaft. Nope you can not use this shaft again. The waterpump will always leak coolant. Sadly you can buy ALL waterpump parts, but NOT the waterpump shaft. We need to replace the waterpump by a new one.
Always use some grease when you install/insert the waterpump in it's housing. Otherwise the O-rings get damaged and coolant will leak into the engine.
Always use some grease when you install/insert the waterpump in it's housing. Otherwise the O-rings get damaged and coolant will leak into the engine.
The waterpump has leaked the very aggressive coolant. The M6 banjo bolt is severe corroded en together with the corroded material the banjo bolt is clogged.
The waterpump has leaked the very aggressive coolant. The M6 banjo bolt is severe corroded en together with the corroded material the banjo bolt is clogged.
.... The by pass canal to the cylinderheads thermostat housing will be clogged. You will certainly get some temerature problems.
.... The by pass canal to the cylinderheads thermostat housing will be clogged. You will certainly get some temerature problems.
The engine inside O-ring is installed, but when you use TO MUCH sealant you will get troubles........
The engine inside O-ring is installed, but when you use TO MUCH sealant you will get troubles........
Ignition cable guide installed at the wrong side of the engine.
Ignition cable guide installed at the wrong side of the engine.
The waterpump is on the bottom of the engine.
The waterpump is on the bottom of the engine.
Open ignition side of the engine.
Open ignition side of the engine.
Open clutchside of the engine.
Open clutchside of the engine.
Someone forgot to install the small seal for the secundairy gear shaft, the oil plate, at the engines bottom, collects oil and that oil has to get into this shaft. When this seal is missing the oil won't get into the gear shaft.
Someone forgot to install the small seal for the secundairy gear shaft, the oil plate, at the engines bottom, collects oil and that oil has to get into this shaft. When this seal is missing the oil won't get into the gear shaft.
The other half of the woodruf-key is in the starter clutch itself.
The other half of the woodruf-key is in the starter clutch itself.
Of course the woodruf-key will break after a while. This means this engine would NOT RUN with this broken woodruf-key because the ignition timing is far out of range.
Of course the woodruf-key will break after a while. This means this engine would NOT RUN with this broken woodruf-key because the ignition timing is far out of range.
Loose starter clutch nut.
Loose starter clutch nut.
Someone didn't do his job properly! The starter clutch NUT, which has to be torqued on 50Nm was loose. That's why we, at KnalNaarPotz, make notes for CRITICAL jobs done as: Starter clutch nut torqued at 50Nm.
Someone didn't do his job properly! The starter clutch NUT, which has to be torqued on 50Nm was loose. That's why we, at KnalNaarPotz, make notes for CRITICAL jobs done as: Starter clutch nut torqued at 50Nm.
At the former rebuild they used a BOGUS gasket set, the footer gasket was very sticky and it took us an hour to remove the footer gasket and cleaning the surfaces. Due to the BOGUS gasket set the cylinder head gasket leaked EVERY WHERE. When installing the barrel ALWAYS use the FOUR O-rings (and NOT THREE as in the former rebuild) on the footer gasket, even when it is a blind hole.
At the former rebuild they used a BOGUS gasket set, the footer gasket was very sticky and it took us an hour to remove the footer gasket and cleaning the surfaces. Due to the BOGUS gasket set the cylinder head gasket leaked EVERY WHERE. When installing the barrel ALWAYS use the FOUR O-rings (and NOT THREE as in the former rebuild) on the footer gasket, even when it is a blind hole.
Piston small-end.
Piston small-end.
The crankshaft has been rebuild before.
The crankshaft has been rebuild before.
No we won't use these pistons again. There is some damage on the pistons.
No we won't use these pistons again. There is some damage on the pistons.
Still the standard bore of 70mm, There are some marks on this pistons. So the rebore will be the next one with 70+0,5mm.
Still the standard bore of 70mm, There are some marks on this pistons. So the rebore will be the next one with 70+0,5mm.
Due to all the problems we discovered on this engine the piston's won't fit in the barrel anymore.
Due to all the problems we discovered on this engine the piston's won't fit in the barrel anymore.
The GT750 engine: Barrel removed, the footer gasket is very sticky on the footer surface.
The GT750 engine: Barrel removed, the footer gasket is very sticky on the footer surface.
SITE UPDATE 25082025: Disassembling the GT750 engine for a complete rebuild. This engine was opened lately as we can see, but we needed the barrel pulling bolts to remove the barrel.
SITE UPDATE 25082025: Disassembling the GT750 engine for a complete rebuild. This engine was opened lately as we can see, but we needed the barrel pulling bolts to remove the barrel.
GT750 engine to be rebuild.
GT750 engine to be rebuild.
GT750 engine to be rebuild.
So we removed the engine out of the frame. Engine near the bike for disassembling, inspecting and the rebuild.
So we removed the engine out of the frame. Engine near the bike for disassembling, inspecting and the rebuild.
So we removed the engine out of the frame.
So we removed the engine out of the frame.
So we removed the engine out of the frame.
IT IS GETTING MORE WORSE! We did a complete ROTATE of the crankshaft with a 14 wrench, BUT there was no movement of the pistons in the barrel. So it is possible that the wood-ruf key is broken. Due to all these problems we will expect a lot more problems in this engine we and the client decided to inspect and rebuild the complete engine of this GT750.
IT IS GETTING MORE WORSE! We did a complete ROTATE of the crankshaft with a 14 wrench, BUT there was no movement of the pistons in the barrel. So it is possible that the wood-ruf key is broken. Due to all these problems we will expect a lot more problems in this engine we and the client decided to inspect and rebuild the complete engine of this GT750.
IT IS GETTING WORSE AND WORSE! We did the small-end and big-end piston test, NOT GOOD, on the LEFT and CENTER we have the small-end and big-end out of tolerance what you can hear in the test by a clicking sound. In this case we recommend the client to do a complete rebuild of the engine.
IT IS GETTING WORSE AND WORSE! We did the small-end and big-end piston test, NOT GOOD, on the LEFT and CENTER we have the small-end and big-end out of tolerance what you can hear in the test by a clicking sound. In this case we recommend the client to do a complete rebuild of the engine.
This cilinder looks very very bad, all covered with rust. It looks like an engine what have been parked in a shed for a long long time. It is better to rebore this barrel and install new pistons.
This cilinder looks very very bad, all covered with rust. It looks like an engine what have been parked in a shed for a long long time. It is better to rebore this barrel and install new pistons.
This cilinder looks very very bad, all covered with rust. It looks like an engine what have been parked in a shed for a long long time. It is better to rebore this barrel and install new pistons.
This cilinder looks very very bad, all covered with rust. It looks like an engine what have been parked in a shed for a long long time. It is better to rebore this barrel and install new pistons.
You can see a lot of rust on the barrel top surface, the head gasket was leaking coolant every where.
You can see a lot of rust on the barrel top surface, the head gasket was leaking coolant every where.
Removed the cilinder head today, looks bad, you can see that the complete head gasket was leaking coolant.
Removed the cilinder head today, looks bad, you can see that the complete head gasket was leaking coolant.
WE WILL NEVER UNDERSTAND WHAT's in someones mind to work like this way. Why use NON-leaking washer on SEVEN M10 bolts and use 4 normal washer on the other M10 head bolts. Besides that the NON leaking washers were to small for these M10 bolts because they are not OEM SUZUKI, the rubbers in the washer were all damaged and leaked coolant.
WE WILL NEVER UNDERSTAND WHAT's in someones mind to work like this way. Why use NON-leaking washer on SEVEN M10 bolts and use 4 normal washer on the other M10 head bolts. Besides that the NON leaking washers were to small for these M10 bolts because they are not OEM SUZUKI, the rubbers in the washer were all damaged and leaked coolant.
Very rusty STAINLESS steel M10 head bolts, this due to the leaking cilinder head.
Very rusty STAINLESS steel M10 head bolts, this due to the leaking cilinder head.
Leaking M10 bolts on the cilinderhead. As said already we will "TRY" to replace the cilinder head gasket due to this severe leaking.
Leaking M10 bolts on the cilinderhead. As said already we will "TRY" to replace the cilinder head gasket due to this severe leaking.
As we removed the fuel tank of the bike the leaking M10 bolts of the cilinder head are better visable. Yes they are extreme leaking. Did a test torque on one M10 bolt, less the 30Nm, as these M10 bolts have to be torqued and retorqued on 40Nm.
As we removed the fuel tank of the bike the leaking M10 bolts of the cilinder head are better visable. Yes they are extreme leaking. Did a test torque on one M10 bolt, less the 30Nm, as these M10 bolts have to be torqued and retorqued on 40Nm.
Needed to change the, TO THICK oil hose on the filled 2stroke oil tank, so we we drained the oil tank. NOTE: The former owner used very thick 2stroke oil. The problem with the to this 2stroke oil hose that this hose was bend to mouch and created a 2stroke oil startvation for the engine.
Needed to change the, TO THICK oil hose on the filled 2stroke oil tank, so we we drained the oil tank. NOTE: The former owner used very thick 2stroke oil. The problem with the to this 2stroke oil hose that this hose was bend to mouch and created a 2stroke oil startvation for the engine.
Filters installed on the checked SRIS valves.
Filters installed on the checked SRIS valves.
Installing new parts, filters for the SRIS valves and two rubbers for the rear inner mudgard.
Installing new parts, filters for the SRIS valves and two rubbers for the rear inner mudgard.
The MINUS brush close up, this one will last longer then the PLUS brush, but we had to replace this brush too. As you can see compared to the old and new brush.
The MINUS brush close up, this one will last longer then the PLUS brush, but we had to replace this brush too. As you can see compared to the old and new brush.
After the cleanig we install both new brushes in the electrical starter engine.
After the cleanig we install both new brushes in the electrical starter engine.
SITE UPDATE 22082025: Got another NEWER type of electrical starter engine, the left one. Of course we will clean and rebuild the USED electrical starter engine. We will replace the brushes too.
SITE UPDATE 22082025: Got another NEWER type of electrical starter engine, the left one. Of course we will clean and rebuild the USED electrical starter engine. We will replace the brushes too.
Three different colored spark plugs, the center sparkplug has the right burning proces.. There is something wrong with both: ignition timing and carburettors.
Three different colored spark plugs, the center sparkplug has the right burning proces.. There is something wrong with both: ignition timing and carburettors.
Cleaned the greasy groundplate of the ignition points. Also replaced the ignition points by new points, adjusted the opening of the points on 0,35mm. No we didn't adjust the timing because there is something wrong with the cilinder head gasket. We really NEED this one to be replaced. (later on)
Cleaned the greasy groundplate of the ignition points. Also replaced the ignition points by new points, adjusted the opening of the points on 0,35mm. No we didn't adjust the timing because there is something wrong with the cilinder head gasket. We really NEED this one to be replaced. (later on)
Repaired, finished and installed calipers. No blocking brakes anymore.
Repaired, finished and installed calipers. No blocking brakes anymore.
Repaired, finoshed and installed calipers. No blocking brakes anymore.
Repaired, finoshed and installed calipers. No blocking brakes anymore.
The cause of leaking the brake fluid is found, the seat of the square O-ring for the brake pisten is very rough due to corrosion from the past. We will advise the client to replace this caliper by another one.
The cause of leaking the brake fluid is found, the seat of the square O-ring for the brake pisten is very rough due to corrosion from the past. We will advise the client to replace this caliper by another one.
Some rust on the piston of this caliper. This means brake flued was leaking.
Some rust on the piston of this caliper. This means brake flued was leaking.
It was hard to remove one of the M10 inbus bolt from the front brake caliper RIGHT side, what's wrong with it. After disassembling the complete caliper we see that both O-rings on the bolt dispappeared and are pulverized. How is that pssible. Of course now we now whta caused the blocking btrakes.
It was hard to remove one of the M10 inbus bolt from the front brake caliper RIGHT side, what's wrong with it. After disassembling the complete caliper we see that both O-rings on the bolt dispappeared and are pulverized. How is that pssible. Of course now we now whta caused the blocking btrakes.
Disassembled the first front brake caliper LEFT side, all looks fine and new. This side can't cause the blocking brakes.
Disassembled the first front brake caliper LEFT side, all looks fine and new. This side can't cause the blocking brakes.
The client has bought the GT750 with steel brake lines installed.
The client has bought the GT750 with steel brake lines installed.
The client has bought the GT750 with steel brake lines installed.
Side view of the two front brake calipers.
Side view of the two front brake calipers.
SITE UPDATE 19082025: Started today with removing the front brake calipers. We noticed that when pushing the bike you needed a lot of force for that. A short test confirmed: Blocking calipers, so clean and in case off rebuild.
SITE UPDATE 19082025: Started today with removing the front brake calipers. We noticed that when pushing the bike you needed a lot of force for that. A short test confirmed: Blocking calipers, so clean and in case off rebuild.
Finished carburettor block (21).
Finished carburettor block (21).
Finished carburettor block (21).
Finished carburettor block (21).
Finished carburettor block (21). (NOTE it also possible to install the anti surge jets at the back of the carburettor.
Finished carburettor block (21). (NOTE it also possible to install the anti surge jets at the back of the carburettor.
Finished carburettor block (21).
Finished carburettor block (21).
Finished carburettor block (21).
Finished carburettor block (21). NOTE: The connection rubbers are installed properly.
Finished carburettor block (21). NOTE: The connection rubbers are installed properly.
And of course we install the small filter on the needle valve.
And of course we install the small filter on the needle valve.
All three carburettors cleaned and ready for assembling. And NO, when you don't do it this way with the RIGHT adjustments and jets in the carburettors the GT engine won't run properly and you can start again with celaning the carburettors. You will understand that a leaking, filled with fuel, float is not OK.
All three carburettors cleaned and ready for assembling. And NO, when you don't do it this way with the RIGHT adjustments and jets in the carburettors the GT engine won't run properly and you can start again with celaning the carburettors. You will understand that a leaking, filled with fuel, float is not OK.
See the difference, LEFT a dirty carburettor, RIGHT a cleaned carburettor.
See the difference, LEFT a dirty carburettor, RIGHT a cleaned carburettor.
So we can start to CLEAN all three carburettors.
So we can start to CLEAN all three carburettors.
All parts of the three carburettors.
All parts of the three carburettors.
Disassembled the complete carburettor block for rebuild. Found a couple of defect parts: a leaking float. The carburettors haven't had a rebuild before, the old 45 pilot jet and the 107,5 main jet's were still inside.
Disassembled the complete carburettor block for rebuild. Found a couple of defect parts: a leaking float. The carburettors haven't had a rebuild before, the old 45 pilot jet and the 107,5 main jet's were still inside.
Inside the carburettor is also very dirty. This means (done a lot of CV carburettors) at least THREE hrs of cleaning and polishing.
Inside the carburettor is also very dirty. This means (done a lot of CV carburettors) at least THREE hrs of cleaning and polishing.
Never seen so much corrosion on the brass parts of a carburettor. I think they used WRONG FUEL as E10 (Euro 95). Always use E5 or Euro 98.
Never seen so much corrosion on the brass parts of a carburettor. I think they used WRONG FUEL as E10 (Euro 95). Always use E5 or Euro 98.
Very dirty. Sadly they had forgotton to install the small filter on the needle valve.
Very dirty. Sadly they had forgotton to install the small filter on the needle valve.
Although the float bowls are not extreme dirty the carburettor itself is very dirty with corrosion and OLD FUEL residues. These carburettors aren't cleaned for a long time. NOTE: This carburettor block seems to have less wear.
Although the float bowls are not extreme dirty the carburettor itself is very dirty with corrosion and OLD FUEL residues. These carburettors aren't cleaned for a long time. NOTE: This carburettor block seems to have less wear.
Why not buy the right parts for the vacuum connection? At www.knalnaarpotz.nl we have replacement caps.
Why not buy the right parts for the vacuum connection? At www.knalnaarpotz.nl we have replacement caps.
After the total rebuild of the oil pump we do a so called bench check, the oil pump PASSED the bench-check. We check the oil pump if it works as it should do outside the GT engine.
After the total rebuild of the oil pump we do a so called bench check, the oil pump PASSED the bench-check. We check the oil pump if it works as it should do outside the GT engine.
Filling the oil pump with red 2stroke oil. After the total rebuild of the oil pump we do a so called bench check, the oil pump PASSED the bench-check. We check the oil pump if it works fine as it should do outside the GT engine.
Filling the oil pump with red 2stroke oil. After the total rebuild of the oil pump we do a so called bench check, the oil pump PASSED the bench-check. We check the oil pump if it works fine as it should do outside the GT engine.
The three needed parts. For your information, you need a special tool for installing the (small) lever seal. The gasket is only available at www.knalnaarpotz.nl
The three needed parts. For your information, you need a special tool for installing the (small) lever seal. The gasket is only available at www.knalnaarpotz.nl
The bottom rotor shaft seal. Will be replaced by a new one.
The bottom rotor shaft seal. Will be replaced by a new one.
The oil pump lever shaft, due to the age of the oil pump lever seal this seal is hardened and worn, the reason of leaking the 2stroke oil.
The oil pump lever shaft, due to the age of the oil pump lever seal this seal is hardened and worn, the reason of leaking the 2stroke oil.
The oil pump body and rotor. Of course everything will be cleaned and inspected.
The oil pump body and rotor. Of course everything will be cleaned and inspected.
Disassembling the oil pump head for cleaning and rebuild.
Disassembling the oil pump head for cleaning and rebuild.
Look at the lever shaft (some yellow on it) you can see that the shaft seal is leaking.
Look at the lever shaft (some yellow on it) you can see that the shaft seal is leaking.
Rebuilding the oil pump. So we first start to disassemble the oil pump.
Rebuilding the oil pump. So we first start to disassemble the oil pump.
SITE UPDATE 18082025: Hangtest Nr2 performed for about 72hrs. This test FAILED, because there are three oil lines empty, i mean these oil lines don't have 2stroke anymore. But they should: This means THREE check-valves are defect. NOTE: Explanation, when the 2stroke oil runs out of the oil lines means that the engine can be filled with TO MUCH 2stroke oil.
SITE UPDATE 18082025: Hangtest Nr2 performed for about 72hrs. This test FAILED, because there are three oil lines empty, i mean these oil lines don't have 2stroke anymore. But they should: This means THREE check-valves are defect. NOTE: Explanation, when the 2stroke oil runs out of the oil lines means that the engine can be filled with TO MUCH 2stroke oil.
SADLY, the empty oil lines are those lines where they have exchanged the check-valve connections itself. Nope we can't repair this any more. We will replace this oil lines by another refurbished one with SIX new check-valves.
SADLY, the empty oil lines are those lines where they have exchanged the check-valve connections itself. Nope we can't repair this any more. We will replace this oil lines by another refurbished one with SIX new check-valves.
Back side of the oil lines, here you can see better that three oil lines don't have 2stroke oil in it.
Back side of the oil lines, here you can see better that three oil lines don't have 2stroke oil in it.
Close-up of the oil line check-valve connection.
Close-up of the oil line check-valve connection.
And YES, leaking oil lines at the chack-valve connection. Someone did a bad job. The connection from the check-valve connection hose to the oil line hose itself was loose. QUESTION: How to repair now? The oil lines are very rare at this moment. Try to find one?
And YES, leaking oil lines at the chack-valve connection. Someone did a bad job. The connection from the check-valve connection hose to the oil line hose itself was loose. QUESTION: How to repair now? The oil lines are very rare at this moment. Try to find one?
Noooo, someone tampered on the oil lines already! When the check-valves are defect we can't change these anymore, because the connection is now different.
Noooo, someone tampered on the oil lines already! When the check-valves are defect we can't change these anymore, because the connection is now different.
In the electrical starter bay we found a lot of 2stroke oil. We know already what that means: Leaking oil lines or leaking banjo bolts.
In the electrical starter bay we found a lot of 2stroke oil. We know already what that means: Leaking oil lines or leaking banjo bolts.
BUT: This is an older type electrical starter engine, this one doesn't have enough power any way. We will replace the electrical starter by another NEWER type electrical starter engine.
BUT: This is an older type electrical starter engine, this one doesn't have enough power any way. We will replace the electrical starter by another NEWER type electrical starter engine.
This is the reason why we needed to disassemble all these parts on this GT750: Bad electrical starter engine. BUT: This is an older type electrical starter engine, this one doesn't have enough power any way. We will replace the electrical starter by another NEWER type electrical starter engine.
This is the reason why we needed to disassemble all these parts on this GT750: Bad electrical starter engine. BUT: This is an older type electrical starter engine, this one doesn't have enough power any way. We will replace the electrical starter by another NEWER type electrical starter engine.
CAUTION: Always be sure that the 2stroke oil hose is making the right smooth turn, so NOT LIKE THIS. It is possible that the oil hose will be closed in total, so the engine don't get any 2stroke oil in this position. See a servive bulletin of SUZUKI: OIL STARVATION.
CAUTION: Always be sure that the 2stroke oil hose is making the right smooth turn, so NOT LIKE THIS. It is possible that the oil hose will be closed in total, so the engine don't get any 2stroke oil in this position. See a servive bulletin of SUZUKI: OIL STARVATION.
CAUTION: Always be sure that the 2stroke oil hose is making the right smooth turn, so NOT LIKE THIS. It is possible that the oil hose will be closed in total, so the engine don't get any 2stroke oil in this position. See a servive bulletin of SUZUKI: OIL STARVATION.
Just leaking fuel at the drain plug of the carburettor.
Just leaking fuel at the drain plug of the carburettor.
EHhhhh...... someone did't look at the details, this notch on the carburettor rubber should be in the total down position. This is a second time i see this.
EHhhhh...... someone did't look at the details, this notch on the carburettor rubber should be in the total down position. This is a second time i see this.
EHhhhh...... someone did't look at the details, this notch on the carburettor rubber should be in the total down position. This is a second time i see this.
Very dirty carburettors. Not cleaned for a long time. These carburettors are also leaking fuel in the cylinders when you forget to turn the fule tap from PRI to NORMAL.
Very dirty carburettors. Not cleaned for a long time. These carburettors are also leaking fuel in the cylinders when you forget to turn the fule tap from PRI to NORMAL.
See the picture of the electrical starter engine: When you use 10mm2 on the electrical starter engine its's mandatory to use also a ground wire of 10mm2 from the battery to the frame! This ground wire is much to thin, yoe can see that at the connector it has been very hot already.
See the picture of the electrical starter engine: When you use 10mm2 on the electrical starter engine its's mandatory to use also a ground wire of 10mm2 from the battery to the frame! This ground wire is much to thin, yoe can see that at the connector it has been very hot already.
Notice the THICK plus 12Volt wire at the elektrical starter engine. This is a 10mm2 wire.
Notice the THICK plus 12Volt wire at the elektrical starter engine. This is a 10mm2 wire.
So we corrected this by using NORMAL and adequate connectors.
So we corrected this by using NORMAL and adequate connectors.
NO NO NO, This is NOT THE WAY connecting wire's! The wire connection with such (blue) connectors are much to small and will heat up by using the bike.
NO NO NO, This is NOT THE WAY connecting wire's! The wire connection with such (blue) connectors are much to small and will heat up by using the bike.
So rerouting finished! This looks much better! You easy can access the battery and the 2stroke oil filling cap.
So rerouting finished! This looks much better! You easy can access the battery and the 2stroke oil filling cap.
So rerouting almost finished! This looks much better! You easy can access the battery and the 2stroke oil filling cap.
So rerouting almost finished! This looks much better! You easy can access the battery and the 2stroke oil filling cap.
For rerouting the wire loom we have to make: SPAGHETTI.
For rerouting the wire loom we have to make: SPAGHETTI.
For rerouting the wire loom we have to make: SPAGHETTI.
For rerouting the wire loom we have to make: SPAGHETTI.
The (new) wire loon Nr2 is damaged already due to the wrong routing. As you can see the ORANGE WIRE: is a switched 12Volt power wire is visable already. No this needs to be repaired and to be changed.
The (new) wire loon Nr2 is damaged already due to the wrong routing. As you can see the ORANGE WIRE: is a switched 12Volt power wire is visable already. No this needs to be repaired and to be changed.
WRONG SIDE ROUTED wire loom Nr2, the wire loom is routed at the right side of the frame, and blocking the battery and the 2stroke oil filling cap.
WRONG SIDE ROUTED wire loom Nr2, the wire loom is routed at the right side of the frame, and blocking the battery and the 2stroke oil filling cap.
Duh, what's this, why is the wire loom Nr2 routed at the RIGHT side of the bike. All the wire's at the end of the wire loom Nr2 blockes access to the battery and the oil filling cap. This needs to be changed!
Duh, what's this, why is the wire loom Nr2 routed at the RIGHT side of the bike. All the wire's at the end of the wire loom Nr2 blockes access to the battery and the oil filling cap. This needs to be changed!
We ALWAYS DRAIN the engine FIRST when we get an unknown bike at www.knalnaarpotz.nl. This because we know that after more then 50years the check-valves in the oil lines have defects. In this case NOT OIL but a lot of fuel in the LEFT and CENTER cylinder, this because of OLD and leaking carburettors.
We ALWAYS DRAIN the engine FIRST when we get an unknown bike at www.knalnaarpotz.nl. This because we know that after more then 50years the check-valves in the oil lines have defects. In this case NOT OIL but a lot of fuel in the LEFT and CENTER cylinder, this because of OLD and leaking carburettors.
We ALWAYS DRAIN the engine FIRST when we get an unknown bike at www.knalnaarpotz.nl. This because we know that after more then 50years the check-valves in the oil lines have defects. In this case NOT OIL but a lot of fuel in the LEFT and CENTER cylinder, this because of OLD and leaking carburettors.
SAFETY ISSUE: Loose handlebar grip RIGHT, imagine what can happen when you do a mergency stop; RECOMMENDATION: Replace by genuine handlebar grips.
SAFETY ISSUE: Loose handlebar grip RIGHT, imagine what can happen when you do a mergency stop; RECOMMENDATION: Replace by genuine handlebar grips.
SITE UPDATE 14082025: SAFETY ISSUE: Loose handlebar grip LEFT, imagine what can happen when you do a mergency stop; RECOMMENDATION: Replace by genuine handlebar grips.
SITE UPDATE 14082025: SAFETY ISSUE: Loose handlebar grip LEFT, imagine what can happen when you do a mergency stop; RECOMMENDATION: Replace by genuine handlebar grips.
SAFETY ISSUE: Wrong passenger foot rests and placed on the wrong position, to much to the front. Why a safety issue? This because the genuine foot rests will be in a locked position in a provision for on the frame, so the footrests can't turn over when someone uses the foot rests.
SAFETY ISSUE: Wrong passenger foot rests and placed on the wrong position, to much to the front. Why a safety issue? This because the genuine foot rests will be in a locked position in a provision for on the frame, so the footrests can't turn over when someone uses the foot rests.
SADLY, they used the wrong bolts for installing the exhausts. The nut on the small exhaust pipe is M10x1,25 (metric fine) so you should use a bolt with the same threading and not with standard threading. The threading in the small exhausts are now damaged. Besides that, the bolt is much TO LONG and can hit the swing arm.
SADLY, they used the wrong bolts for installing the exhausts. The nut on the small exhaust pipe is M10x1,25 (metric fine) so you should use a bolt with the same threading and not with standard threading. The threading in the small exhausts are now damaged. Besides that, the bolt is much TO LONG and can hit the swing arm.
SADLY, they used the wrong bolts for installing the exhausts. The nut on the small exhaust pipe is M10x1,25 (metric fine) so you should use a bolt with the same threading and not with standard threading. The threading in the small exhausts are now damaged.
SADLY, they used the wrong bolts for installing the exhausts. The nut on the small exhaust pipe is M10x1,25 (metric fine) so you should use a bolt with the same threading and not with standard threading. The threading in the small exhausts are now damaged.
Doesn't look nice on this bike, we will replace the to large washer for the original cap on the brake pedal.
Doesn't look nice on this bike, we will replace the to large washer for the original cap on the brake pedal.
This looks like a bad rebuild of the Suzuki GT750 engine! You need the special washer to prevent coolant leaking on the M10 head bolts. The former rebuilder just used a normal washer.
This looks like a bad rebuild of the Suzuki GT750 engine! You need the special washer to prevent coolant leaking on the M10 head bolts. The former rebuilder just used a normal washer.
This looks like a bad rebuild of the Suzuki GT750 engine! There are THREE coolant leaking M10 head bolts which are rusty now. You need the special washer to prevent coolant leaking on the M10 head bolts. The former rebuilder just used a normal washer. We will see what we can do without removing the cylinderhead.
This looks like a bad rebuild of the Suzuki GT750 engine! There are THREE coolant leaking M10 head bolts which are rusty now. You need the special washer to prevent coolant leaking on the M10 head bolts. The former rebuilder just used a normal washer. We will see what we can do without removing the cylinderhead.
ALWAYS on a unknown 2stroke SUZUKI GT bike: Drain the cylinders for 2stroke oil and/or fuel.
ALWAYS on a unknown 2stroke SUZUKI GT bike: Drain the cylinders for 2stroke oil and/or fuel.
SAFETY ISSUE: Bad brakes, it's hard to push the bike on it's place for repair. The brake pads are blocking the brake-disks.
SAFETY ISSUE: Bad brakes, it's hard to push the bike on it's place for repair. The brake pads are blocking the brake-disks.
SAFETY ISSUE: Bad brakes, it's hard to push the bike on it's place for repair. The brake pads are blocking the brake-disks.
SAFETY ISSUE: Why is the rear sprocket not secured in the right way? 18082025 IT IS EVEN WORSE! All the nuts for fastening the rear sprocket weren't tightened!. We corrected this safety problem and secured the nuts.
SAFETY ISSUE: Why is the rear sprocket not secured in the right way? 18082025 IT IS EVEN WORSE! All the nuts for fastening the rear sprocket weren't tightened!. We corrected this safety problem and secured the nuts.
We wil clean, rebuild and adjust all three carburettors with new parts.
We wil clean, rebuild and adjust all three carburettors with new parts.
Leaking carburettors, as you can see under the carburettors on top of the GT750 engine. We will clean rebuild and adjust all three carburettors with new parts.
Leaking carburettors, as you can see under the carburettors on top of the GT750 engine. We will clean rebuild and adjust all three carburettors with new parts.
SAFETY ISSUE: Why connect the fuel hose to short and like a piano string? Leaking fuel can cause fire, so this needs to be repaired.
SAFETY ISSUE: Why connect the fuel hose to short and like a piano string? Leaking fuel can cause fire, so this needs to be repaired.
Overview of this "very" nice GT750. Sadly we found some maintenance and safety issues that needs to be repaired.
Overview of this "very" nice GT750. Sadly we found some maintenance and safety issues that needs to be repaired.
Overview of this "very" nice GT750. Sadly we found some maintenance and safety issues that needs to be repaired.
Overview of this "very" nice GT750. Sadly we found some maintenance and safety issues that needs to be repaired.
Just for tagging: Motor revisie GT750 GT550 GT380 T20 T500 GT250 T350 krukas revisie cilinder boren en honen polijsten onderdelen waterpomp zuigers onderhoud reparatie vervanging wet-blasting
Just for tagging: Motor revisie GT750 GT550 GT380 T20 T500 GT250 T350 krukas revisie cilinder boren en honen polijsten onderdelen waterpomp zuigers onderhoud reparatie vervanging wet-blasting
SITE START 13082025: A Suzuki GT750-B came in at KNALNAARPOTZ shop for some repairs and large maintenance. We will repair: Electrical starter, oil-lines rebuild, oil-pump rebuild, cylinder head M10 bolts leaking, rebuild the front brakes and much more also safety repairs. 29082025 After we did some work on this GT750 we discovered that the engine needed a complete rebuild, this because the former owner ran the bike with RUSTY cylinders, so all the rust damaged all the bearings of the crankshaft.
SITE START 13082025: A Suzuki GT750-B came in at KNALNAARPOTZ shop for some repairs and large maintenance. We will repair: Electrical starter, oil-lines rebuild, oil-pump rebuild, cylinder head M10 bolts leaking, rebuild the front brakes and much more also safety repairs. 29082025 After we did some work on this GT750 we discovered that the engine needed a complete rebuild, this because the former owner ran the bike with RUSTY cylinders, so all the rust damaged all the bearings of the crankshaft.

Parts for this bike

All parts Suzuki GT750

Got a project of your own?

Rebuild, restoration or maintenance: call, message or email us to book the workshop.

Contact us